You are here: Installation > Hyper-V installations > Deploying a Conferencing Node

Manually deploying a Conferencing Node on a Hyper-V host

Before you start, ensure that you are currently using the same machine that you will subsequently want to use to upload the generated file on to your host server.

To manually deploy a new Conferencing Node on to a Hyper-V host:

  1. Go to Platform configuration > Conferencing Nodes and select Add Conferencing Node.
  2. From the Deployment type field, select Manual (Hyper-V).
  3. Select Next.
  4. You are now asked to provide information regarding the CPUs and memory of the Conferencing Node VM, by completing the following fields:

    Option Description
    Number of virtual CPUs to assign Enter the number of virtual CPUs to assign to the Conferencing Node. We recommend no more than one virtual CPU per physical core, unless you are making use of CPUs that support hyperthreading — see NUMA affinity and hyperthreading for more details.
    System memory (in megabytes) to assign

    Enter the amount of RAM (in megabytes) to assign to the Conferencing Node. The number entered must be a multiple of 4.

    We recommend 1024 MB (1 GB) RAM for each virtual CPU.

  5. Select Next.
  6. You are now asked to provide the network configuration to be applied to the Conferencing Node, by completing the following fields:

    Option Description
    Name Enter the name that will be used to refer to this Conferencing Node in the Pexip Infinity Administrator interface.
    Description An optional field where you can provide more information about the Conferencing Node.
    Hostname

    Domain

    Enter the hostname and domain to be assigned to this Conferencing Node. Each Conferencing Node and Management Node must have a unique hostname.

    The Hostname and Domain together make up the Conferencing Node's DNS name or FQDN. We recommend you assign valid DNS names to all your Conferencing Nodes. For more information, see Assigning hostnames and FQDNs.

    IPv4 address Enter the IP address to be assigned to this Conferencing Node when it is created.
    Network mask Enter the IP network mask to be assigned to this Conferencing Node.
    Gateway IPv4 address Enter the IP address of the default gateway to be assigned to this Conferencing Node.
    Secondary interface IPv4 address The optional secondary interface IPv4 address for this Conferencing Node. If configured, this interface is used for signaling and media communications to clients, and the primary interface is used for communication with the Management Node and other Conferencing Nodes. For more information, see Conferencing Nodes with dual network interfaces (NICs).
    Secondary interface network mask The optional secondary interface network mask for this Conferencing Node.
    System location

    Select the physical location of this Conferencing Node.

    If the system location does not already exist, you can create a new one here by clicking to the right of the field. This will open up a new window showing the Add system location page. For further information see About system locations.

    SIP TLS FQDN A unique identity for this Conferencing Node, used in signaling SIP TLS Contact addresses. For more information, see SIP TLS FQDN.
    TLS certificate The TLS certificate to use on this node. This must be a certificate that contains the above SIP TLS FQDN. Each certificate is shown in the format <subject name> (<issuer>).
    IPv6 address The IPv6 address for this Conferencing Node. Each Conferencing Node must have a unique IPv6 address.
    Gateway IPv6 address The IPv6 address of the default gateway.
    IPv4 static NAT address

    The public IPv4 address used by this Conferencing Node when it is located behind a NAT device. Note that if you are using NAT, you must also configure your NAT device to route the Conferencing Node's IPv4 static NAT address to its IPv4 address.

    For more information, see Configuring Pexip Infinity nodes to work behind a static NAT device.

    Static routes From the list of Available Static routes, select the routes to assign to the node, and then use the right arrow to move the selected routes into the Chosen Static routes list. For more information, see Managing static routes.
    Enable distributed database

    This should usually be enabled (checked) for all Conferencing Nodes that are expected to be "always on", and disabled (unchecked) for nodes that are expected to only be powered on some of the time (e.g. cloud bursting nodes that are likely to only be operational during peak times).

    SSH password

    Enter the password to be used when logging in to this Conferencing Node's Linux operating system over SSH. The username will always be admin.

    Logging in to the operating system is required when changing passwords or for diagnostic purposes only, and should generally be done under the guidance of your Pexip authorized support representative. In particular, do not change any configuration using SSH — all changes should be made using the Pexip Infinity Administrator interface.

  7. Select Finish.

    You will be taken to the Manually Deploy Conferencing Node page.

  8. Select Download Conferencing Node.

    A zip file with the name pexip-<hostname>.<domain>.zip will be downloaded.

  9. When you wish to deploy the Conferencing Nodes:

    1. Copy the zip file to the server running Hyper-V and unzip it.
      You will see a subfolder called Virtual Machines, containing an XML file which contains the configuration for the Conferencing Node VM.
    2. Open the Hyper-V Manager and select Import Virtual Machine....
    3. Follow the on-screen prompts to deploy the Conferencing Node VM.

      When prompted, select the Virtual Machines folder and the Hyper-V manager will automatically discover the XML file.

      Select the type of import most appropriate for your environment (if you are unsure, select Restore the virtual machine).

After deploying a new Conferencing Node, it takes approximately 5 minutes before the node is available for conference hosting and for its status to be updated on the Management Node. (Until it is available, the Management Node will report the status of the Conferencing Node as having a last contacted and last updated date of "Never".)

To look at the steps taken in setting up an example lab deployment of a Conferencing Node in Microsoft Hyper-V, see http://www.graham-walsh.com/2016/02/setting-up-pexip-infinity-with-microsoft-hyper-v-server-2012/.

Enabling automatic startup

By default, virtual machines deployed using Hyper-V are configured to restart automatically if they were running when the host server was shut down or powered off. We recommend that you leave this setting as is for the Management Node and all Conferencing Nodes.

Disabling processor compatibility mode

We strongly recommend that you disable processor compatibility mode on all Hyper-V Conferencing Node virtual machines. If processor compatibility mode is enabled, the Conferencing Node may assume it is running on older hardware, and may stop working, with the message CPU instruction set is not supported; system will be placed in maintenance mode.

For more information, see https://technet.microsoft.com/en-us/library/dn859550.aspx.

Next steps

See Next steps after initial installation.